Aerospace EngineeringTextbook

Multiple-Input Describing Functions and Nonlinear System Design

Not rated yetRate this book

Arthur Gelb and Wallace E. Vander Velde’s Multiple-Input Describing Functions and Nonlinear System Design develops approximate methods for analyzing nonlinear feedback systems under different kinds of input. This guide follows its nine chapters and eight appendices, with particular attention to the assumptions behind equivalent linearization.

FormatExternal access
LanguageEnglish
SubjectAerospace Engineering
LevelNot specified
No. of pages—
PublishedNot specified

Free reading is available at the official source. Opens in a new tab.

Multiple-Input Describing Functions and Nonlinear System DesignFree

About this book

Arthur Gelb and Wallace E. Vander Velde’s Multiple-Input Describing Functions and Nonlinear System Design develops approximate methods for analyzing nonlinear feedback systems under different kinds of input. This guide follows its nine chapters and eight appendices, with particular attention to the assumptions behind equivalent linearization.

How to study this book

Review linear feedback, frequency response, Fourier analysis, and probability. For every describing function, state the nonlinearity, input class, amplitude conventions, and retained output component. Check approximate predictions against time-domain calculations where possible. A describing-function result is not automatically a rigorous stability proof for the original nonlinear system.

Chapter-wise explanations and study tasks

Chapter 1 — Nonlinear Systems and Describing Functions

The opening distinguishes nonlinear behavior from linear superposition and presents describing functions as a structured approximation. Its unified viewpoint makes the chosen input class central to the linearized representation.

Study task: Compare a local small-signal linearization with a describing-function approximation for a simple saturation element.

Chapter 2 — Sinusoidal-Input Describing Function

The sinusoidal describing function relates a prescribed sinusoidal input to an equivalent response component. The chapter treats calculation, frequency-dependent and independent nonlinearities, approximation, synthesis, and inversion.

Study task: Compute a fundamental-harmonic approximation for a stated memoryless nonlinearity and compare it with its full output waveform.

Chapter 3 — Steady-State Oscillations

Limit-cycle prediction, stability, forced response, compensation, and multiple nonlinearities are examined through the sinusoidal approximation. The chapter also considers accuracy and exact relay methods, making verification a central concern.

Study task: Predict a candidate oscillation for a simple feedback example and test its frequency and amplitude by simulation.

Chapter 4 — Transient Oscillations

The analysis extends beyond a stationary oscillation to changing amplitude and phase. Distinguish an evolving oscillatory envelope from a steady limit cycle and track the assumptions that make an approximate transient description possible.

Study task: Compare a simulated oscillation’s amplitude envelope with an approximate prediction and identify where the agreement deteriorates.

Chapter 5 — Two-Sinusoid-Input Describing Function

Two sinusoidal components can interact through a nonlinearity, producing behavior a single-input approximation misses. Subharmonics, multiple limit cycles, and incremental-input analysis motivate the richer representation.

Study task: Apply two tones to a simple nonlinearity and inspect output frequencies that are absent from a single-tone test.

Chapter 6 — Dual-Input Describing Function

The dual-input framework develops calculations for interacting input components and applies them to forced limit-cycle behavior, adaptation, asymmetry, and dither. Identify the specific input combination before selecting a formula.

Study task: Compare an asymmetric element with and without a bias or dither input and explain the change in effective behavior.

Chapter 7 — Random and Other Signals

Statistical linearization and random-input describing functions connect nonlinear responses with input distributions and noise. A result derived for Gaussian input need not remain appropriate after the input statistics change.

Study task: Estimate an equivalent gain from simulated random input and compare it under two different input distributions.

Chapter 8 — Nonoscillatory Transients

Transient-input and exponential-input descriptions address responses that are not dominated by a continuing oscillation. The chapter links approximations with a design procedure for a specified transient objective.

Study task: Compare the approximate and simulated response to a nonoscillatory input and state which transient feature your model captures.

Chapter 9 — Nonlinear Sampled-Data Oscillations

Sampling changes the possible oscillation modes and their stability. Relay and other sampled nonlinear systems, exact verification, and pulse-width-modulated examples require attention to the discrete timing as well as the nonlinearity.

Study task: Simulate a sampled nonlinear loop at two sampling intervals and test whether a predicted periodic mode persists.

Appendix A — Amplitude and Decibels

The conversion table supports consistent movement between amplitude ratios and decibel values. Identify whether a plotted quantity is an amplitude ratio before applying the relevant logarithmic conversion.

Study task: Convert three amplitude ratios to decibels and check the inverse conversion numerically.

Appendix B — Sinusoidal Describing-Function Tables

These tables provide results for particular nonlinearities and conventions. Match the input amplitude and element parameters exactly rather than choosing a formula only because its label sounds familiar.

Study task: Select one table entry and independently derive or numerically verify it at two input amplitudes.

Appendix C — Dual-Input Tables

The dual-input tables encode dependence on more than one input characteristic. Inspect parameter ranges and normalization before inserting a result into a feedback calculation.

Study task: Document all arguments of a selected dual-input function and verify a suitable limiting case.

Appendix D — Two-Sinusoid Tables

The two-sinusoid tables support calculations involving interacting tones. Preserve the meaning of each amplitude and frequency component when comparing the tabulated result with an experiment.

Study task: Numerically test one table entry and identify which output component is represented.

Appendix E — Random-Input Tables

The random-input tables distinguish Gaussian, Gaussian-plus-bias, and Gaussian-plus-bias-plus-sinusoid settings. Their statistical assumptions are part of the model, not optional labels.

Study task: Choose the correct input family for a hypothetical noisy signal and explain why the other table families differ.

Appendix F — Sampled Describing Functions

Sampled-system tables support the oscillation analysis in Chapter 9. The sampling convention and periodic sequence must match the calculation being performed.

Study task: Cross-check a sampled table result against a directly generated periodic sequence.

Appendix G — Filter Hypothesis

The analytical discussion examines the filtering assumption underlying the method. It helps readers ask whether neglected waveform components are actually suppressed strongly enough in the loop.

Study task: Compare retained and neglected harmonics after the linear subsystem and assess whether the approximation is plausible.

Appendix H — Probability and Random Processes

The probability reference supports statistical linearization and random-input analysis. Review the required distribution and process concepts before treating a random describing function as a deterministic constant.

Study task: Relate the moments used in a random-input approximation to estimates obtained from simulated samples.

Applied assignment

Analyze one simple nonlinear feedback loop using a describing function and a time-domain simulation. Specify the nonlinearity and input assumptions, predict a response feature, and measure the discrepancy. Repeat with a second input class or sampling interval and explain whether the changed result reflects a violated assumption or an expected limitation.

Suggested reading plan

Study Chapters 1–3 for the basic method and steady oscillations, then Chapter 4 for transients. Read Chapters 5–7 for richer input classes and Chapters 8–9 for nonoscillatory and sampled behavior. Use the matching appendix while performing each calculation, and finish with the filter-hypothesis review.

Questions for reflection

  • Which output components does your approximation discard?
  • Does a candidate oscillation prediction establish its existence or stability?
  • What changes when input statistics or sampling conventions change?

Edition and source notes

This guide follows the Gelb and Vander Velde textbook distributed through MIT’s estimation-and-control course resource. Its nine chapters are followed by Appendices A–H. It is a classical nonlinear-control text: the supplementary examples are educational analyses, not validated controller designs for the source’s historical application systems.

Consult the official source and full text.

About access & copyright

This page provides book information and study material. Full-text access is provided by the original publisher or authorised source; a listing does not grant permission to republish the book.

Read our Library Access & Copyright policy

Explore the contents

Check the chapters covered in this edition.

Visit the official source

See reading, preview or purchase options.

Save for later

Keep this textbook in your saved collection.

Reader ratings & reviews

Be the first to rate

No ratings yet

0%0%
0%0%
0%0%
0%0%
0%0%

Share your thoughts

Your review helps other students choose the right resources.

Rate this book

How helpful was this book?No sign-up needed. Your rating appears instantly.